微機灰熔點測定儀攝像頭的調試方法

2025-12-17 　來自: 鶴壁市淇天儀器儀表有限公司. 瀏覽次數:143

微機灰熔點測定儀攝像頭的調試方法

Ash melting point camera debugging

安裝好攝像頭后，攝像頭距離灰熔點爐體的間距為150mm

After installing the camera, the distance between the camera and the ash melting point furnace body is 150mm

攝像頭介紹

Camera Introduction

攝像頭三個旋鈕調整，從前到后作用分別是：

The three knobs of the camera are adjusted, and their effects from front to back are:

調整畫面大小

Adjusting the screen size

調整畫面明暗

Adjusting the brightness of the screen

調整畫面清晰度

Adjusting the clarity of the screen

畫面調整

Screen adjustment

設備開始后，溫度達到900℃時彈出提示。不要點擊對話框中的“知道了”，這時開始調整攝像頭。注意：調整速度要快，設備到1000℃后系統會自動開始實驗，導致調整失效

After the device starts, a prompt will pop up when the temperature reaches 900 ℃. Don't click on "Got it" in the dialog box, then start adjusting the camera. Attention: The adjustment speed should be fast. After the device reaches 1000 ℃, the system will automatically start the experiment, causing the adjustment to fail

先調整畫面焦距，就是攝像頭zui內側的旋鈕，調整到樣品邊緣清晰即可。如下圖

First adjust the focal length of the image, which is the innermost knob of the camera, until the sample edge is clear. As shown in the following figure

然后用攝像頭中間那個旋鈕來調整畫面的亮度，不能太亮也不能太暗。如下圖

Then use the knob in the middle of the camera to adjust the brightness of the image, which should not be too bright or too dark. As shown in the following figure

最后調整畫面大小，用攝像頭zui外側的，先將帶編號的方框完整框住樣品，尖頭部分不需要完全頂住“編號方框”的頂部。

Finally, adjust the picture size. Use the outermost part of the camera to completely frame the sample with the numbered box. The pointed part does not need to completely support the top of the "numbered box".

畫面調整好之后點擊彈出對話框中的“知道了”

After adjusting the screen, click "Got it" in the pop-up dialog box

然后用鼠標點擊界面中的“原型”畫面。

Then click on the "prototype" screen in the interface with the mouse.

點擊過“原型”畫面后，系統會固定目前的亮度，然后就算灰熔點測定儀攝像頭調試完畢

After clicking on the "prototype" screen, the system will fix the current brightness, and then even after debugging is completed

具體詳情可聯系鶴壁淇天公司進行咨詢0392-3388939 3388929